Contact Us

NEED PRESSURIZED IRRIGATION?


Introducing the 2" Riser + 30 or 40 psi

The KAP-IT+ includes a regulator built into the 2” stem so that you can more effectively water your lawn or bed areas. With the Kap-It + you can maximize water pressure to 30 or 40 PSI across all heads. This balances out the water distribution and makes the flow the same throughout your sprinklers in a given zone.

The pressure regulator in the Kap-It + will also make any sprinklers compliant with the laws that require pressure regulation, so you don’t have to replace your whole head to meet state requirements. Several states require that any sprinklers that are installed or need to be upgraded or worked on must have pressure regulation. With the Kap-It + you now can add to an existing sprinkler to make the sprinkler have pressure regulation.

You can do this in the flower beds or anywhere you use shrub adapters. Kap-It+ has a nozzle guard on top of the sprinkler to protect the nozzles that are becoming more and more expensive over time. The nozzle guard allows for the nozzle to sit down into the sprinkler and be protected.

There is slot on the side of the Kap so that you can get a small flat screw driver on top to lift the nozzle and acts as a drain for water as the system turns on and off. The Kap-It + includes all the best parts and functionality of the original Kap-It. The

Features & Benefits

• 2” stem vs. the 1.5” stem

• Nozzle guard protection with drain

• Can be stacked on top of the original Kap-It and vice versa.

• Pressure regulated in the 2” stem

• Pressure Regulated at 30 or 40 PSI

• The 40 lbs. in the riser will maintain

• Example (30 or 40 PSI) on all fixed spray nozzles up to 4 GPM. With an inlet greater than 50 PSI)

• Most nozzles on the market work in Kap-IT+

• Rubber gasket is included to put on the filter as it will be placed below the riser.

• Can use the pressure regulated stem on a shrub adapter in flower and bush beds, islands, mulch (bark, rock) etc.

Media

Kap-IT+ Kap-IT+ Riser

Kap-IT+ Riser Install

Diagram

Frequently Asked Questions

What makes the product innovative?

Kap-IT allows anyone to raise a sprinkler head from the top instead of from the bottom!

By extending the stem of a standard riser, you have raised the height. The new snap on top protects the stem extension, while leaving all of manufacturer’s original parts completely intact. Kap-IT keeps the rocks and debris normally introduced into the head when a sprinkler is unscrewed, below ground. The snap on top is designed to still allow regular access to the inside of the head itself, by maintaining the ability to unscrew the top of the canister with the Kap-IT - even when more than one is stacked.

This solution is Simple, Secure, Fast, and Permanent. Jump up your nozzle with a Kap-I.

How does your product improve water/resource use efficiency?

When a sprinkler is not above the grass blade height, even the most advanced water saving nozzles distribute water inefficiently. Blockage of the water stream causes increased water waste and run off.

As a standard cure to extend the life of risers that are too low, home owners start lowering the deck height of their mowers. This increases soil temperatures and evaporation, and requires extended water run times. Thereby increasing water needs.

By making it fast, and easy enough for anyone to raise their sprinkler heads, watering stays efficient, and distribution is maximized.

Describe how the end user uses the product.

Kap-IT is designed for the homeowner and professional alike. With this product, you are able to quickly clean around the top of the sprinkler cap. Simply unscrew the nozzle and add the stem extender. Next, slide the Cap Extender over the stem and snap it down onto the existing cap. Replace the nozzle and align.

The only thing else to it, is you can add more than one to stack them and add extra height! Plus, you can use it to unscrew the canister cap.

What is your product's life expectancy/warranty?

Life expectancy of the Kap-IT is equal to the head it is being attached to. Kap-IT is made to take a beating, and because there is no changing in the original head structure or workings, there is minimal possibility of failure.

Kap-IT has a One-Year warranty against manufacturer defects. 

Contact Us

info@kjketterlingenterprises.com

(208) 280-0964